Menu:Options

From Win-Test Wiki
Revision as of 08:12, 4 August 2006 by I2WIJ (Talk | contribs) (WAEDC)

Jump to: navigation, search

Load contest at startup

Enables or disables the automatic loading of the last contest file in use. This command is useful to get on line again quickly if - for some reason - Win-Test crashed or you had to quit the Win-Test in the middle of the contest.

If you like to switch to another file, close this file using file File | Close an then File | Open menu dialog.

Automatic backup...

automatic-backups.png
This enables or disables the automatic backup of the .wtb file to another location, e.g. network drive or floppy. You can choose between 1 and 120 minutes as automatic backup intervall.


Disable log synchronization on network

If checked, automatic log synchronization over the network (in multi/op environments) is disabled. May be useful under certain circumstances.

CW

No sound

If checked, no CW sound will be played through the internal speaker. This option is also available through the SOUND/NOSOUND text commands.

Modify standard messages

The place to change the CW messages.

cw-standard-messages.png

Please have a look on the list of message variables.

Modify additional messages

The place to create or modify additional CW messages which can be accessed using Alt-C. These memories can be used for transmitting QSL information, special greetings, QSY/sked information, ...

cw-additional-messages.png

Serial number

The leading zeros below 100 can be (or not) keyed by Win-Test, depending on the chosen option.

Similarly, there are 5 possible abbreviation levels for the serial numbers :

  • Not abbreviated
  • Half abbreviated : leading zeros are replaced by T.
  • Abbreviated : The 0 and the 9 are shortened in T and N.
  • Pro : The 0, 1, 4, 5 and 9 are shortened to T, A, V, E and N.
  • Custom - there is a custom table. so each number can be shortened to a letter of your choice. Have fun.

This option only affects serial numbers, but never numbers in callsigns.

Correction

controls the value of the $CORRECTED variable. See message variables for more information.

Shortened spaces (CT spaces)

The standard spacing between CW words is 7 dits length, instead of 6 (known as "CT space"). With this option you can set it back to 6 dits if you want, achieving slightly shorter spacing between words. You can also use the new text commands CTSPACE and NOCTSPACE to set or reset it.

Auto sending...

This allows to automatically start sending the INSERT message after some characters are entered in the callsign field.

configuring autosending

Configure interfaces...

All the interfaces you wish to use with Win-Test can be parametered by using this dialog box.

Interface configuration

The serial ports can be used for the network (with crossed cables), for a connection to a packet radio controller, or for a RS232 radio interface. In that last case, you must specify what transceiver you are using. You also need to verify the port configuration :

Serial port configuration

The DTR(4)/RTS(7) pins can be controlled as

  • Handshake
  • PTT
  • CW
  • Always on
  • Always off
  • Active radio

The parallel ports can only be used to interface the CW output from Win-Test via a classical interface. You just need to specify, in the dialog box, which radio is connected to the parallel port. More, the delay between the PTT command and the effective CW transmission is adjustable between 0 (QSK) to 1000 ms.

Parallel port configuration

The Ethernet interface is used by the Win-Test's local area network, in a multi-operating environment. If needed, you can change the broadcast address and the port number used. If you ignore the meaning of these terms, note that there should normally be no need to modify the default values given by Win-Test. See Networking for more information.

At last, if your computer has an embedded sound card, you can select and use it as a digital voice keyer by checking the appropriate box.

If you want to use a third-party software to record or modify voice messages, be sure to use the following file format : WAV, PCM, 8000 Hz sampling frequency, 1 channel (mono) and 16 bits per sample.

WinKey configuration...

TODO winkey configuration

EZMaster configuration...

TODO ezmaster configuration

RTTY configuration...

This menu entry opens the control box for RTTY configuration.

Log

Allows to choose display of the LOG: fonts, colors, headings and so on.

Spots warnings

When this option is enabled, the DX cluster spots are briefly displayed (as soon as they arrive), under the lower line of the logging fields. You can choose to display only the spots of the current band and/or the new mulitpliers, as well as your own callsign (good to know when You're spotted). Of course You can hide Dupes and invalids.

DX cluster shortcuts

This controls the syntax of the DX-cluster used (DX Spider vs. AK1A, DXNet, etc.) and the count of spots and solar information used.

HamCAP

TODO HamCAP

WAEDC

Special option for the Worked All Europe DX Contest.

For more informations about Win-Test and WAEDC see WAEDC.

Data files

This option ontrols which CTY.DAT to use, and can even start an immediate download from win-test.com.

Windows

The child windows can be included in the main Win-Test window, or floating, thus allowing the Windows desktop or other running softwares to remain visible. Please remember that, depending on your computer and/or operating system capabilities, you can monitor Win-Test on more than one screen.

Toolbar

If this option is checked, the Icons toobar is displayed below the menu.

Icon toolbar

Language

It is possible to choose the language of the Win-Test user interface. Currently supported languages are English, French and German.

Selecting the Language

Back to Menus